DS413J qui ne démarre plus

[DensLeonis]

Bonjour à tous,

j'ai remplacé le Disque 3 sur mon DS413J qui donnait de signes de faiblesses.

lors du calcul de cohérence de parité, le nas m'indiquait que le disque 2 avait des erreurs de secteurs mais le contrôle continuait.

A 64% le nas a planté et maintenant la led power clignote de même que la led réseau mais rien de plus, il ne s'éteint même pas quand je garde le bouton appuyé.

j'ai à tout hasard changé le disque 2 mais je n'ai toujorus pas accès à l'interface donc je ne sais pas si je peux recontrauire le RAID, là j'ai beau chercher, cela dépasse mes compétences.

 

Si vous avez une idée 😞 merci

 

je peux me connecter en SSH et dsmesg m'indique :

dmesg
[    0.000000] Linux version 2.6.32.12 (root@build4) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #25556 Thu Jul 1 14:25:48 CST 2021
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Synology 6282 board
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Sys Clk = 200000000, Tclk = 166666667
[    0.000000] Synology Board ID: 26
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 131072
[    0.000000] free_area_init_node: node 0, pgdat c03f3a14, node_mem_map c1001000
[    0.000000]   Normal zone: 1024 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 130048 pages, LIFO batch:31
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,8M root=/dev/md0 rw syno_hw_version=DS413jv10 ihd_num=4 netif_num=1 flash_size=8
[    0.000000] Synology Hardware Version: DS413jv10-j
[    0.000000] Internal HD num: 4
[    0.000000] Internal netif num: 1
[    0.000000] Flash Memory Size: 8 MB
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 512MB = 512MB total
[    0.000000] Memory: 502784KB available (3656K code, 519K data, 124K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 1589.24 BogoMIPS (lpj=7946240)
[    0.240000] Mount-cache hash table entries: 512
[    0.240000] CPU: Testing write buffer coherency: ok
[    0.240000] devtmpfs: initialized
[    0.240000] xor: measuring software checksum speed
[    0.290000]    arm4regs  :  1448.400 MB/sec
[    0.340000]    8regs     :   869.200 MB/sec
[    0.390000]    32regs    :  1122.000 MB/sec
[    0.390000] xor: using function: arm4regs (1448.400 MB/sec)
[    0.390000] NET: Registered protocol family 16
[    0.390000] Feroceon L2: Enabling L2
[    0.390000] Feroceon L2: Cache support initialised, in WT override mode.

[    0.410000] CPU Interface
[    0.410000] -------------
[    0.410000] SDRAM_CS0 ....base 00000000, size 512MB
[    0.410000] SDRAM_CS1 ....disable
[    0.410000] SDRAM_CS2 ....disable
[    0.410000] SDRAM_CS3 ....disable
[    0.410000] PEX0_MEM ....base e0000000, size 128MB
[    0.410000] PEX0_IO ....base f2000000, size   1MB
[    0.410000] PEX1_MEM ....base e8000000, size 128MB
[    0.410000] PEX1_IO ....base f2100000, size   1MB
[    0.410000] INTER_REGS ....base f1000000, size   1MB
[    0.410000] NFLASH_CS ....base fa000000, size   2MB
[    0.410000] SPI_CS ....base f4000000, size  16MB
[    0.410000] BOOT_ROM_CS ....no such
[    0.410000] DEV_BOOTCS ....no such
[    0.410000] CRYPT_ENG ....base f0000000, size   2MB
[    0.410000]  Detected Tclk 200000000 and SysClk 533333333
[    0.410000] Apply DS 413j GPIO
[    0.410000] Synology 6282 DS411 GPIO Init
[    0.410000] PCIe link is enable, apply PCIe workaround
[    0.910000] PEX0 interface detected Link X4
[    1.410000] PEX1 interface detected no Link.
[    1.410000] pci 0000:00:01.0: reg 10 64bit mmio: [0x14000000-0x140fffff]
[    1.410000] pci 0000:00:01.0: reg 18 io port: [0x00-0xff]
[    1.410000] PCI: bus0: Fast back to back transfers disabled
[    1.410000] PCI: bus1: Fast back to back transfers enabled
[    1.420000] bio: create slab <bio-0> at 0
[    1.420000] vgaarb: loaded
[    1.420000] SCSI subsystem initialized
[    1.420000] libata version 3.00 loaded.
[    1.590000] raid6: int32x1    126 MB/s
[    1.760000] raid6: int32x2    185 MB/s
[    1.930000] raid6: int32x4    180 MB/s
[    2.100000] raid6: int32x8    193 MB/s
[    2.100000] raid6: using algorithm int32x8 (193 MB/s)
[    2.100000] Switching to clocksource kw_clocksource
[    2.100000] NET: Registered protocol family 2
[    2.100000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    2.100000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    2.100000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[    2.100000] TCP: Hash tables configured (established 16384 bind 16384)
[    2.100000] TCP reno registered
[    2.100000] NET: Registered protocol family 1
[    2.100000] RPC: Registered udp transport module.
[    2.100000] RPC: Registered tcp transport module.
[    2.100000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    2.100000] Trying to unpack rootfs image as initramfs...
[    5.040000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[    5.060000] Freeing initrd memory: 8192K
[    5.060000] XOR registered 4 channels
[    5.060000] XOR 2nd invalidate WA enabled
[    5.060000] VFS: Disk quotas dquot_6.5.2
[    5.060000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    5.060000] msgmni has been set to 998
[    5.060000] alg: No test for md5 (md5-generic)
[    5.060000] alg: No test for des (des-generic)
[    5.060000] alg: No test for des3_ede (des3_ede-generic)
[    5.060000] alg: No test for stdrng (krng)
[    5.060000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    5.060000] io scheduler noop registered
[    5.060000] io scheduler anticipatory registered (default)
[    5.070000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    5.070000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    5.080000] console [ttyS0] enabled
[    5.080000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[    5.100000] brd: module loaded
[    5.100000] sata_mv 0000:00:01.0: version 1.28
[    5.100000] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[    5.110000] sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[    5.120000] scsi0 : sata_mv
[    5.120000] scsi1 : sata_mv
[    5.120000] scsi2 : sata_mv
[    5.130000] scsi3 : sata_mv
[    5.130000] ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 9
[    5.140000] ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 9
[    5.150000] ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 9
[    5.150000] ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 9
[   13.710000] ata1: link is slow to respond, please be patient (ready=0)
[   17.130000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   17.290000] ata1.00: ATA-9: WDC WD40EFRX-68WT0N0, 80.00A80, max UDMA/133
[   17.290000] ata1.00: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[   17.320000] ata1.00: configured for UDMA/133
[   17.340000] scsi 0:0:0:0: Direct-Access     WDC      WD40EFRX-68WT0N0         80.0 PQ: 0 ANSI: 5
[   17.340000] sd 0:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[   17.350000] sd 0:0:0:0: [sda] 4096-byte physical blocks
[   17.360000] sd 0:0:0:0: [sda] Write Protect is off
[   17.360000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   17.360000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   17.370000]  sda: sda1 sda2 sda5 sda6
[   17.450000] sd 0:0:0:0: [sda] Attached SCSI disk
[   20.450000] Delay 5 seconds to wait for disk 2 ready.
[   31.000000] ata2: link is slow to respond, please be patient (ready=0)
[   34.900000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   34.940000] ata2.00: ATA-10: ST4000VN006-3CW104, SC60, max UDMA/133
[   34.940000] ata2.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[   35.010000] ata2.00: configured for UDMA/133
[   35.030000] scsi 1:0:0:0: Direct-Access     ATA      ST4000VN006-3CW104       SC60 PQ: 0 ANSI: 5
[   35.030000] sd 1:0:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[   35.040000] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[   35.050000] sd 1:0:0:0: [sdb] Write Protect is off
[   35.050000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   35.050000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   35.060000]  sdb: unknown partition table
[   35.090000] sd 1:0:0:0: [sdb] Attached SCSI disk
[   38.090000] Delay 5 seconds to wait for disk 3 ready.
[   48.640000] ata3: link is slow to respond, please be patient (ready=0)
[   52.360000] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   52.400000] ata3.00: ATA-10: ST4000VN006-3CW104, SC60, max UDMA/133
[   52.400000] ata3.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[   52.470000] ata3.00: configured for UDMA/133
[   52.490000] scsi 2:0:0:0: Direct-Access     ATA      ST4000VN006-3CW104       SC60 PQ: 0 ANSI: 5
[   52.490000] sd 2:0:0:0: [sdc] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[   52.500000] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[   52.510000] sd 2:0:0:0: [sdc] Write Protect is off
[   52.510000] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[   52.510000] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   52.520000]  sdc: sdc1 sdc2 sdc5 sdc6
[   52.580000] sd 2:0:0:0: [sdc] Attached SCSI disk
[   55.580000] Delay 5 seconds to wait for disk 4 ready.
[   66.130000] ata4: link is slow to respond, please be patient (ready=0)
[   68.650000] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   68.710000] ata4.00: ATA-10: ST4000DM004-2CV104, 0001, max UDMA/133
[   68.710000] ata4.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[   68.800000] ata4.00: configured for UDMA/133
[   68.820000] scsi 3:0:0:0: Direct-Access     ATA      ST4000DM004-2CV104       0001 PQ: 0 ANSI: 5
[   68.820000] sd 3:0:0:0: [sdd] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[   68.830000] sd 3:0:0:0: [sdd] 4096-byte physical blocks
[   68.840000] sd 3:0:0:0: [sdd] Write Protect is off
[   68.840000] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[   68.840000] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   68.850000]  sdd: sdd1 sdd2 sdd5 sdd6
[   68.920000] sd 3:0:0:0: [sdd] Attached SCSI disk
[   68.930000] sata_mv sata_mv.0: version 1.28
[   68.930000] sata_mv sata_mv.0: slots 32 ports 2
[   68.940000] scsi4 : sata_mv
[   68.940000] scsi5 : sata_mv
[   68.950000] ata5: SATA max UDMA/133 irq 21
[   68.950000] ata6: SATA max UDMA/133 irq 21
[   69.300000] ata5: SATA link down (SStatus 0 SControl F300)
[   69.650000] ata6: SATA link down (SStatus 0 SControl F300)
[   69.650000] physmap platform flash device: 00400000 at f8000000
[   69.660000] SPI Serial flash detected @ 0xf8000000, 8192KB (128sec x 64KB)
[   69.670000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x7f0000
[   69.680000] 6 RedBoot partitions found on MTD device SYNOMTD-0
[   69.690000] SYNOMTD flash bank 0: Using RedBoot partition definition
[   69.690000] Creating 6 MTD partitions on "SYNOMTD-0":
[   69.700000] 0x000000000000-0x000000090000 : "RedBoot"
[   69.710000] 0x000000090000-0x000000390000 : "zImage"
[   69.710000] 0x000000390000-0x0000007d0000 : "rd.gz"
[   69.720000] 0x0000007d0000-0x0000007e0000 : "vendor"
[   69.720000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[   69.730000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[   69.730000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[   69.740000] serial number='C7KVN01114'
[   69.740000] 0x0000007e0000-0x0000007f0000 : "RedBoot Config"
[   69.750000] 0x0000007f0000-0x000000800000 : "FIS directory"
[   69.760000] SPI Serial flash detected @ 0xf4000000, 8192KB (128sec x 64KB)
[   69.770000] cmdlinepart partition parsing not available
[   69.770000] Loading Marvell Ethernet Driver:
[   69.780000]   o Cached descriptors in DRAM
[   69.780000]   o DRAM SW cache-coherency
[   69.780000]   o 2 Giga ports supported
[   69.790000]   o Single RX Queue support - ETH_DEF_RXQ=0
[   69.790000]   o Single TX Queue support - ETH_DEF_TXQ=0
[   69.800000]   o TCP segmentation offload (TSO) supported
[   69.800000]   o Receive checksum offload supported
[   69.810000]   o Transmit checksum offload supported
[   69.810000]   o SKB Recycle supported - (Enabled)
[   69.820000]   o Rx descripors: q0=128
[   69.820000]   o Tx descripors: q0=532
[   69.830000]   o Loading network interface(s):
[   69.830000]     o  register under mv88fx_eth platform
[   69.840000]     o eth0, ifindex = 2, GbE port = 0
[   69.840000]     o eth0, phy chipid = 1410e90, Support WOL = 32

[   69.850000] md: linear personality registered for level -1
[   69.850000] md: raid0 personality registered for level 0
[   69.860000] md: raid1 personality registered for level 1
[   69.860000] md: raid10 personality registered for level 10
[   69.870000] md: raid6 personality registered for level 6
[   69.880000] md: raid5 personality registered for level 5
[   69.880000] md: raid4 personality registered for level 4
[   69.890000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[   69.900000] cpuidle: using governor ladder
[   69.900000] TCP cubic registered
[   69.900000] NET: Registered protocol family 17
[   69.910000] NET: Registered protocol family 15
[   69.910000] registered taskstats version 1
[   69.920000] md: Waiting for all devices to be available before autodetect
[   69.920000] md: If you don't use raid, use raid=noautodetect
[   69.930000] md: Autodetecting RAID arrays.
[   69.950000] md: invalid raid superblock magic on sda2
[   69.960000] md: sda2 does not have a valid v0.90 superblock, not importing!
[   69.990000] md: invalid raid superblock magic on sda5
[   69.990000] md: sda5 does not have a valid v0.90 superblock, not importing!
[   70.020000] md: invalid raid superblock magic on sda6
[   70.030000] md: sda6 does not have a valid v0.90 superblock, not importing!
[   70.060000] md: invalid raid superblock magic on sdc2
[   70.060000] md: sdc2 does not have a valid v0.90 superblock, not importing!
[   70.100000] md: invalid raid superblock magic on sdc5
[   70.100000] md: sdc5 does not have a valid v0.90 superblock, not importing!
[   70.120000] md: invalid raid superblock magic on sdc6
[   70.130000] md: sdc6 does not have a valid v0.90 superblock, not importing!
[   70.160000] md: invalid raid superblock magic on sdd2
[   70.170000] md: sdd2 does not have a valid v0.90 superblock, not importing!
[   70.200000] md: invalid raid superblock magic on sdd5
[   70.210000] md: sdd5 does not have a valid v0.90 superblock, not importing!
[   70.240000] md: invalid raid superblock magic on sdd6
[   70.250000] md: sdd6 does not have a valid v0.90 superblock, not importing!
[   70.250000] md: Scanned 12 and added 3 devices.
[   70.260000] md: autorun ...
[   70.260000] md: considering sda1 ...
[   70.260000] md:  adding sda1 ...
[   70.270000] md:  adding sdc1 ...
[   70.270000] md:  adding sdd1 ...
[   70.270000] md: created md0
[   70.280000] md: bind<sdd1>
[   70.280000] md: bind<sdc1>
[   70.280000] md: bind<sda1>
[   70.290000] md: running: <sda1><sdc1><sdd1>
[   70.290000] raid1: raid set md0 active with 3 out of 4 mirrors
[   70.300000] md0: detected capacity change from 0 to 2549940224
[   70.300000] md: ... autorun DONE.
[   70.310000] RAMDISK: lzma image found at block 0
[   73.450000] VFS: Mounted root (ext2 filesystem) on device 1:0.
[   73.750000] usbcore: registered new interface driver usbfs
[   73.750000] usbcore: registered new interface driver hub
[   73.780000] usbcore: registered new interface driver ethub
[   73.780000] usbcore: registered new device driver usb
[   73.860000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   73.870000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[   73.880000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   73.910000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   73.930000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   73.930000] usb usb1: configuration #1 chosen from 1 choice
[   73.960000] hub 1-0:1.0: USB hub found
[   73.960000] hub 1-0:1.0: 1 port detected
[   74.070000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   74.220000] ds413j_synobios: module license 'Synology Inc.' taints kernel.
[   74.230000] Disabling lock debugging due to kernel taint
[   74.290000] correction with 0x0f
[   74.350000] 2022-9-15 17:21:36 UTC
[   74.350000] synobios: load, major number 201
[   74.350000] Brand: Synology
[   74.360000] Model: DS-413j
[   74.360000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[   74.370000] synobios cpu_arch proc entry initialized
[   74.370000] synobios crypto_hw proc entry initialized
[   74.380000] synobios syno_platform proc entry initialized
[   74.380000] synobios open /dev/ttyS1 success
[   74.390000] usb 1-1: new high speed USB device using orion-ehci and address 2
[   74.410000] synobios: unload
[   74.540000] Got empty serial number. Generate serial number from product.
[   74.550000] usb 1-1: configuration #1 chosen from 1 choice
[   74.550000] hub 1-1:1.0: USB hub found
[   74.580000] hub 1-1:1.0: 4 ports detected
[   74.620000]  md0: unknown partition table
[   79.440000] EXT4-fs (md0): barriers disabled
[   79.460000] EXT4-fs (md0): mounted filesystem with ordered data mode
[   82.070000] EXT3-fs: md0: couldn't mount because of unsupported optional features (240).
[   82.070000] EXT2-fs: md0: couldn't mount because of unsupported optional features (240).
[   82.080000] EXT4-fs (md0): barriers disabled
[   82.100000] EXT4-fs (md0): mounted filesystem with ordered data mode
[   82.100000] VFS: Mounted root (ext4 filesystem) on device 9:0.
[   82.110000] Trying to move old root to /initrd ... okay
[   82.110000] Freeing init memory: 124K
[   91.770000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   91.780000] sd 1:0:0:0: Attached scsi generic sg1 type 0
[   91.790000] sd 2:0:0:0: Attached scsi generic sg2 type 0
[   91.790000] sd 3:0:0:0: Attached scsi generic sg3 type 0
[   94.130000] <30>systemd-udevd[1204]: starting version 204
[  109.810000] md: bind<sda2>
[  109.810000] raid1: raid set md1 active with 1 out of 4 mirrors
[  109.860000] md1: detected capacity change from 0 to 2147418112
[  109.870000]  md1: unknown partition table
[  110.200000] Adding 2097080k swap on /dev/md1.  Priority:-1 extents:1 across:2097080k
[  116.700000] NET: Registered protocol family 10
[  116.710000] lo: Disabled Privacy Extensions
[  116.770000] IPv6 over IPv4 tunneling driver
[  116.780000] sit0: Disabled Privacy Extensions
[  118.380000] init: syno-auth-check main process (2498) killed by TERM signal
[  119.510000] cpufreq: Init kirkwood cpufreq driver
[  119.510000] cpufreq: High frequency: 1600000KHz - Low frequency: 533333KHz
[  120.170000] alg: No test for aes (aes-generic)
[  120.310000] alg: No test for stdrng (ansi_cprng)
[  120.390000] alg: No test for crc32c (crc32c-generic)
[  120.650000] cesadev_init(bf192000)
[  120.710000] mvCesaInit: sessions=10240, queue=64, pSram=f0000000
[  120.850000] alg: No test for sha1 (sha1-generic)
[  120.910000] alg: No test for sha224 (sha224-generic)
[  120.910000] alg: No test for sha256 (sha256-generic)
[  120.990000] encryptfs using the OCF package.
[  121.530000] alg: No test for arc4 (arc4-generic)
[  121.700000] fuse init (API version 7.13)
[  121.930000] exFAT: Version 1.2.9
[  122.280000] sky2 driver version 1.25
[  122.490000] correction with 0x0f
[  122.550000] 2022-9-15 17:22:24 UTC
[  122.550000] synobios: load, major number 201
[  122.560000] Brand: Synology
[  122.560000] Model: DS-413j
[  122.560000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[  122.570000] synobios cpu_arch proc entry initialized
[  122.580000] synobios crypto_hw proc entry initialized
[  122.580000] synobios syno_platform proc entry initialized
[  122.590000] synobios open /dev/ttyS1 success
[  125.040000] eth0: mac address changed
[  127.150000] eth0: link down
[  127.150000] eth0: started
[  127.170000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  128.240000] eth0: link up, full duplex, speed 1 Gbps
[  128.250000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  132.710000] ip_tables: (C) 2000-2006 Netfilter Core Team
[  133.100000] nf_conntrack version 0.5.0 (7990 buckets, 31960 max)
[  136.230000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[  148.050000] md: md2 stopped.
[  148.160000] md: md3 stopped.
[  148.220000] md: bind<sdd6>
[  148.230000] md: bind<sdd5>
[  148.230000] md: bind<sda5>
[  148.230000] md: bind<sdc5>
[  148.330000] md: bind<sdc6>
[  148.330000] md: bind<sda6>
[  148.330000] raid5: device sdc5 operational as raid disk 1
[  148.340000] raid5: device sda5 operational as raid disk 3
[  148.340000] raid5: device sdd5 operational as raid disk 2
[  148.350000] raid5: allocated 4218kB for md2
[  148.360000] raid5: reshape will continue
[  148.360000] raid5: device sda6 operational as raid disk 0
[  148.370000] raid5: device sdc6 operational as raid disk 2
[  148.370000] raid5: device sdd6 operational as raid disk 1
[  148.380000] raid5: allocated 3176kB for md3
[  148.660000] 0: w=1 pa=2 pr=2 m=1 a=2 r=3 op1=0 op2=0
[  148.660000] 2: w=2 pa=2 pr=2 m=1 a=2 r=3 op1=0 op2=0
[  148.670000] 1: w=3 pa=2 pr=2 m=1 a=2 r=3 op1=0 op2=0
[  148.670000] raid5: raid level 5 set md3 active with 3 out of 3 devices, algorithm 2
[  148.680000] RAID5 conf printout:
[  148.680000]  --- rd:3 wd:3
[  148.680000]  disk 0, o:1, dev:sda6
[  148.690000]  disk 1, o:1, dev:sdd6
[  148.690000]  disk 2, o:1, dev:sdc6
[  148.690000] ...ok start reshape thread
[  148.710000] 1: w=1 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0
[  148.710000] 3: w=2 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0
[  148.720000] 2: w=3 pa=0 pr=4 m=1 a=2 r=4 op1=0 op2=0
[  148.720000] raid5: raid level 5 set md2 active with 3 out of 4 devices, algorithm 2
[  148.730000] RAID5 conf printout:
[  148.730000]  --- rd:4 wd:3
[  148.730000]  disk 1, o:1, dev:sdc5
[  148.740000]  disk 2, o:1, dev:sdd5
[  148.740000]  disk 3, o:1, dev:sda5
[  149.000000] md2: detected capacity change from 0 to 8987233222656
[  149.020000]  md2: unknown partition table
[  149.050000] md3: detected capacity change from 0 to 1000086044672
[  149.050000] md: reshape of RAID array md3
[  149.060000] md: minimum _guaranteed_  speed: 2 KB/sec/disk.
[  149.060000] md: using maximum available idle IO bandwidth (but not more than 1 KB/sec) for reshape.
[  149.070000] md: using 128k window, over a total of 976646528 blocks.
[  149.080000]  md3: unknown partition table
[  156.870000] md: md1: set sda2 to auto_remap [0]
[  156.870000] md: md1 stopped.
[  156.880000] md: unbind<sda2>
[  156.880000] md: export_rdev(sda2)
[  156.890000] md1: detected capacity change from 2147418112 to 0
[  157.280000] Adding 2097144k swap on /dev/sda2.  Priority:-1 extents:1 across:2097144k
[  157.510000] Adding 2097144k swap on /dev/sdc2.  Priority:-2 extents:1 across:2097144k
[  157.690000] Adding 2097144k swap on /dev/sdd2.  Priority:-3 extents:1 across:2097144k