ledube Posté(e) le 1 avril 2015 Posté(e) le 1 avril 2015 Bonjour, J'ai dans un RS3614RPxs 6 disques WD4000FYYZ-01UL1B2 en Raid 6. Lors de la création du volume, j'ai sélectionné la version lente (celle qui à priori vérifie toute la surface du disque) en pensant qu'elle était équivalente à une préparation par dd. Malheureusement, il y a quelques jours : 2015/03/29 16:41:13 SYSTEM: Write error at internal disk [1] sector 2193448. Résultat, éjection du hd de la grappe raid, mode dégradé et tout le tralala... L'assistance syno me répond : So it is a disk failure, please replace it, thank you. Donc, je récupère le disque et le passe par l'utilitaire WD. Smart test rapide --> ok Smart test complet --> ok Write 0 --> ok Les résultats de smartctr smartctl 6.3 2014-07-26 r3976 [x86_64-w64-mingw32-win7-sp1] (sf-6.3-1) Copyright © 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 253 253 021 Pre-fail Always - 4658 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 19 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 665 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 4 183 Runtime_Bad_Block 0x0032 096 096 000 Old_age Always - 4 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 2 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 48 194 Temperature_Celsius 0x0022 122 104 000 Old_age Always - 30 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 ********************************************************************************************************************************************************************************************************************************** smartctl 6.3 2014-07-26 r3976 [x86_64-w64-mingw32-win7-sp1] (sf-6.3-1) Copyright © 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 253 253 021 - 4658 4 Start_Stop_Count -O--CK 100 100 000 - 19 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 665 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 4 183 Runtime_Bad_Block -O--CK 096 096 000 - 4 192 Power-Off_Retract_Count -O--CK 200 200 000 - 2 193 Load_Cycle_Count -O--CK 200 200 000 - 48 194 Temperature_Celsius -O---K 122 104 000 - 30 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning ********************************************************************************************************************************************************************************************************************* smartctl 6.3 2014-07-26 r3976 [x86_64-w64-mingw32-win7-sp1] (sf-6.3-1) Copyright © 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Error Log Version: 1 ATA Error Count: 81 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 81 occurred at disk power-on lifetime: 617 hours (25 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 02 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 02 00 00 00 a0 00 24d+23:06:02.971 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 24d+23:06:02.970 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 24d+23:06:02.970 SET FEATURES [set transfer mode] ef 10 02 00 00 00 a0 00 24d+23:06:02.965 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 24d+23:06:02.964 IDENTIFY DEVICE Error occurred at disk power-on lifetime: 617 hours (25 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 45 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 03 45 00 00 00 a0 00 24d+23:06:02.970 SET FEATURES [set transfer mode] ef 10 02 00 00 00 a0 00 24d+23:06:02.965 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 24d+23:06:02.964 IDENTIFY DEVICE ef 10 02 00 00 00 a0 00 24d+23:06:00.659 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 24d+23:06:00.658 IDENTIFY DEVICE Error 79 occurred at disk power-on lifetime: 617 hours (25 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 02 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 02 00 00 00 a0 00 24d+23:06:02.965 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 24d+23:06:02.964 IDENTIFY DEVICE ef 10 02 00 00 00 a0 00 24d+23:06:00.659 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 24d+23:06:00.658 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 24d+23:06:00.658 SET FEATURES [set transfer mode] Error 78 occurred at disk power-on lifetime: 617 hours (25 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 02 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 02 00 00 00 a0 00 24d+23:06:00.659 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 24d+23:06:00.658 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 24d+23:06:00.658 SET FEATURES [set transfer mode] ef 10 02 00 00 00 a0 00 24d+23:06:00.652 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 24d+23:06:00.651 IDENTIFY DEVICE Error 77 occurred at disk power-on lifetime: 617 hours (25 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 45 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 03 45 00 00 00 a0 00 24d+23:06:00.658 SET FEATURES [set transfer mode] ef 10 02 00 00 00 a0 00 24d+23:06:00.652 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 24d+23:06:00.651 IDENTIFY DEVICE ef 10 02 00 00 00 a0 00 24d+23:05:58.347 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 24d+23:05:58.346 IDENTIFY DEVICE **************************************************************************************************************************************************************************************************************************** A votre avis, hd défectueux (donc SAV) ou pas (donc préparation par dd et remise en service) ? Un grand merci ! Sébastien 0 Citer
gaetan.cambier Posté(e) le 1 avril 2015 Posté(e) le 1 avril 2015 Je n'aime pas le runtime bad block qui n'est pas a 0 Pourquoi pas tester le disque avec badblocks -nvs Ça a l'avantage de faire un read write compare et pas juste un write de 0 comme avec dd 0 Citer
Fravadona Posté(e) le 1 avril 2015 Posté(e) le 1 avril 2015 difficile a dire, as-tu activé la veille sur le NAS ? Ca peut etre une cause d'ejection de disque sain par timeout d'ecriture. 0 Citer
ledube Posté(e) le 1 avril 2015 Auteur Posté(e) le 1 avril 2015 Pas de veille activée. Je vais essayer badblocks -nvs ; je vous tiens au courant. 0 Citer
domlas Posté(e) le 1 avril 2015 Posté(e) le 1 avril 2015 Il se peut que sur ton disque tu ais un secteur défectueux placé à un endroit crucial. En usage simpliste ce disque serait parfaitement utilisable mais sur un serveur en RAID cela peut être rédhibitoire. Essaye de le repartitionner et reformater complètement et tente de le réinstaller dans le syno pour voir. Moi je placerais d'office un disque neuf vérifié et je relèguerais celui-là en disque USB ou second disque dans un ordi.. 0 Citer
ledube Posté(e) le 1 avril 2015 Auteur Posté(e) le 1 avril 2015 J'ai un disque neuf de commandé. Celui ci va partir en SAV après les tests. Je me disais qu'en prenant des disques RE je serais tranquille.... j'avais tord... 0 Citer
ledube Posté(e) le 3 avril 2015 Auteur Posté(e) le 3 avril 2015 Salut, Pour badblocks, pas d'erreurs. Par contre un smartctl me donne : Toujours la ligne 183 run time badblock à 4 ainsi que #2 Extended offline Completed: / read failure / 40% / 617heures / LBA 1st error 585688042 Que penser... Merci 0 Citer
Fravadona Posté(e) le 3 avril 2015 Posté(e) le 3 avril 2015 Tu as des secteurs defectueux sur le disque, SAV 0 Citer
ledube Posté(e) le 7 avril 2015 Auteur Posté(e) le 7 avril 2015 Direction SAV. Merci à tous ! 0 Citer
Messages recommandés
Rejoindre la conversation
Vous pouvez publier maintenant et vous inscrire plus tard. Si vous avez un compte, connectez-vous maintenant pour publier avec votre compte.