[DS210J] pb Changement de disques et augmentation du volume

[zheniar]

Bonjour,

J'ai un DS210J avec 2 disques de 1To en miroir. Je veux passer à 2 disques de 2To car je panque de place.

J'ai changé les 2 disques un par un avec réparation du volume à chaque fois pour conserver mes données.

Jusque la tout va bien. Sauf que le volume fait toujours 914Go pour des disques de 1.82To detecté. Le Syno me dit d'ailleur que je peux faire passer le volume à 1860Go environ.

Je fais donc "Gerer" puis "étendre le volume avec l'espace disque non alloué", je valide , le système tourne quelques seconde et jeme retrouve avec tjs mon volume de 914Go..

Que faire? J'ai fais la manip plusieurs fois et rien n'y fait. Une fois j'ai vu le message comme quoi il commencait l'augmentation du volume mais il a vite disparu et le volume est toujours le meme..

En desespoir de cause je pense tout formater et recommencer avec un volume neuf mais j'aimerai garder mes données et ma config :/

J'ai le DSM  5.2-5967 Update 2. dernière mise à jour pour ce Syno..

Merci pour votre aide.

Frédéric

[Mic13710]

Que dit le gestionnaire de stockage ?

De mémoire, l'extension de volume n'est pas instantanée et demande quelques heures. Attendez que l'opération se termine.

[zheniar]

il y a 17 minutes, Mic13710 a dit :

Que dit le gestionnaire de stockage ?

De mémoire, l'extension de volume n'est pas instantanée et demande quelques heures. Attendez que l'opération se termine.

Le gestionnaire de stockage dit "vous pouvez faire passer le volume à 1860Go environ"

Mais j'ai tenté de la faire plusieurs fois en allant dans "Gérer" mais il ne se passe rien.

Le gestionaire ne montre aucune activité, et même en l'ayant laissé tourner toute la nuit c'est toujours pareil.. :(

[Mic13710]

Il faudrait passer par des lignes de commande ce qui se fait sans problème pour l'avoir déjà fait sur un de mes NAS avec l'aide de @gaetan.cambier car ça dépasse mes compétences. Si lui ou un linuxien averti passe par là, il pourrait vous aider.

[zheniar]

Il y a 9 heures, Mic13710 a dit :

Il faudrait passer par des lignes de commande ce qui se fait sans problème pour l'avoir déjà fait sur un de mes NAS avec l'aide de @gaetan.cambier car ça dépasse mes compétences. Si lui ou un linuxien averti passe par là, il pourrait vous aider.

Merci pour cette réponse. cela depase mes competences egalement..

Espérons qu'un linuxien averti passe par la ;)

[Mic13710]

Il y a 14 heures, zheniar a dit :

Merci pour cette réponse. cela depase mes competences egalement..

Espérons qu'un linuxien averti passe par la ;)

Je reprends le sujet.

Si ce n'est pas fait, activez le SSH dans le menu Terminal de DSM. Téléchargez Putty sur votre PC, lancez le et connectez-vous au NAS en renseignant son IP, port 22, connexion SSH. Dans la fenêtre qui s'ouvre vous indiquez pour le login root, et pour le mot de passe celui du compte admin.

Vous tapez ces commandes :

cat /proc/mdstat

parted --list

et vous postez les résultats ici.

[gaetan.cambier]

je vois qu'on me prépare le terrain 

rajoute les commandes suivantes : 

pvs
vgs
lvs

 

[Fenrir]

Un petit apeçu des logs (messages et dmesg)  au moment du soucis d'augmentation ne serait pas un mal non plus, il y a peut être un soucis

[zheniar]

Bonjour,

Merci pour ces réponses, désolé de répondre que maintenant.

voici ce que ces commande donnent.

Pour pvs/vgs,lvs cela semble ne pas fonctionner :/

-----------------------------------------------------------

DiskStation> cat /proc/mdstat
Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4]
md2 : active raid1 sda3[0] sdb3[1]
      973618240 blocks super 1.2 [2/2] [UU]

md1 : active raid1 sda2[1] sdb2[0]
      522048 blocks [2/2] [UU]

md0 : active raid1 sda1[1] sdb1[0]
      2489920 blocks [2/2] [UU]

unused devices: <none>

-------------------------------------------------------------------

DiskStation> parted --list
Warning: Unable to open /dev/hda read-write (Permission denied).  /dev/hda has
been opened read-only.
Model: WDC WD20EFRX-68AX9N0 (scsi)
Disk /dev/hda: 2000GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Disk Flags:

Number  Start   End     Size    Type     File system  Flags
 1      32.3kB  2550MB  2550MB  primary               raid
 2      2550MB  3084MB  535MB   primary               raid
 3      3216MB  2000GB  1997GB  primary               raid

----------------------------------------------------------------------

DiskStation> pvs
  WARNING: Running as a non-root user. Functionality may be unavailable.
DiskStation> vgs
  WARNING: Running as a non-root user. Functionality may be unavailable.
DiskStation> lvs
  WARNING: Running as a non-root user. Functionality may be unavailable.
DiskStation>

Il y a 2 heures, Fenrir a dit :

Un petit apeçu des logs (messages et dmesg)  au moment du soucis d'augmentation ne serait pas un mal non plus, il y a peut être un soucis

Bonne idée en effet et c'est assez étonnant. C'est écrit que ça a fonctionné... alors que j'ai tjs un volume à 914Go pour des disques detectés à 1860Go...

2016-08-06

15:14:42

Information

DiskStation

user

System

System successfully expanded [Volume 1].

2016-08-06

15:14:36

Information

DiskStation

user

System

System starts to expand [Volume 1].

[Fenrir]

Pour les commandes, il faut les faire en root

Comme tu es en DSM5.2, il faut utiliser l'identifiant "root" et le mot de passe du compte "admin"

[zheniar]

il y a 6 minutes, Fenrir a dit :

Pour les commandes, il faut les faire en root

Comme tu es en DSM5.2, il faut utiliser l'identifiant "root" et le mot de passe du compte "admin"

Je suis un boulet.. désolé

du coup ce n'est plus la meme chose.

Par contre pvs vgs et lvs ne donnent rien

Petit détail qui a peut etre son importance, ces diques etaient avant sur mon autre NAS DS213+ que j'ai passé en 4To.

J'ai formaté les disques bien sur.

 

----------------------------------------------------------------------------------

DiskStation> parted --list
Model: WDC WD20EFRX-68AX9N0 (scsi)
Disk /dev/hda: 2000GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Disk Flags:

Number  Start   End     Size    Type     File system  Flags
 1      32.3kB  2550MB  2550MB  primary               raid
 2      2550MB  3084MB  535MB   primary               raid
 3      3216MB  2000GB  1997GB  primary               raid

Model: WDC WD20EFRX-68AX9N0 (scsi)
Disk /dev/sda: 2000GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Disk Flags:

Number  Start   End     Size    Type     File system  Flags
 1      32.3kB  2550MB  2550MB  primary               raid
 2      2550MB  3084MB  535MB   primary               raid
 3      3216MB  2000GB  1997GB  primary               raid

Model: WDC WD20EFRX-68AX9N0 (scsi)
Disk /dev/sdb: 2000GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Disk Flags:

Number  Start   End     Size    Type     File system  Flags
 1      32.3kB  2550MB  2550MB  primary               raid
 2      2550MB  3084MB  535MB   primary               raid
 3      3216MB  2000GB  1997GB  primary               raid

Error: /dev/mtdblock0: unrecognised disk label
Model: Unknown (unknown)
Disk /dev/mtdblock0: 524kB
Sector size (logical/physical): 512B/512B
Partition Table: unknown
Disk Flags:

Error: /dev/mtdblock1: unrecognised disk label
Model: Unknown (unknown)
Disk /dev/mtdblock1: 2097kB
Sector size (logical/physical): 512B/512B
Partition Table: unknown
Disk Flags:

Error: /dev/mtdblock2: unrecognised disk label
Model: Unknown (unknown)
Disk /dev/mtdblock2: 1311kB
Sector size (logical/physical): 512B/512B
Partition Table: unknown
Disk Flags:

Error: /dev/mtdblock3: unrecognised disk label
Model: Unknown (unknown)
Disk /dev/mtdblock3: 65.5kB
Sector size (logical/physical): 512B/512B
Partition Table: unknown
Disk Flags:

Error: /dev/mtdblock4: unrecognised disk label
Model: Unknown (unknown)
Disk /dev/mtdblock4: 131kB
Sector size (logical/physical): 512B/512B
Partition Table: unknown
Disk Flags:

Error: /dev/mtdblock5: unrecognised disk label
Model: Unknown (unknown)
Disk /dev/mtdblock5: 65.5kB
Sector size (logical/physical): 512B/512B
Partition Table: unknown
Disk Flags:

Model: Linux Software RAID Array (md)
Disk /dev/md0: 2550MB
Sector size (logical/physical): 512B/512B
Partition Table: loop
Disk Flags:

Number  Start  End     Size    File system  Flags
 1      0.00B  2550MB  2550MB  ext3

Model: Linux Software RAID Array (md)
Disk /dev/md1: 535MB
Sector size (logical/physical): 512B/512B
Partition Table: loop
Disk Flags:

Number  Start  End    Size   File system     Flags
 1      0.00B  535MB  535MB  linux-swap(v1)

Model: Linux Software RAID Array (md)
Disk /dev/md2: 997GB
Sector size (logical/physical): 512B/512B
Partition Table: loop
Disk Flags:

Number  Start  End    Size   File system  Flags
 1      0.00B  997GB  997GB  ext4

[Fenrir]

il y a 30 minutes, zheniar a dit :

Par contre pvs vgs et lvs ne donnent rien

essaye avec

• pvdisplay
• vgdisplay
• lvdisplay

Il manque aussi le dmesg

[zheniar]

il y a 15 minutes, Fenrir a dit :

essaye avec

• pvdisplay
• vgdisplay
• lvdisplay

Il manque aussi le dmesg

Tjs pareil avec pvdisplay, ca peut venir de putty?

sinon dmesg ci dessous

DiskStation> pvs
DiskStation> vgs
DiskStation> lvs
DiskStation> pvdisplay
DiskStation> vgdisplay
DiskStation> lvdisplay
DiskStation> dmesg
[    0.000000] Linux version 2.6.32.12 (root@build4) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #5967 Tue Apr 26 16:30:14 CST 2016
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Feroceon-KW
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Sys Clk = 200000000, Tclk = 166666667
[    0.000000] Synology Board ID: 21
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat c03f1970, node_mem_map c0c01000
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32512 pages, LIFO batch:7
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS210jv20 ihd_num=2 netif_num=1
[    0.000000] Synology Hardware Version: DS210jv20-j
[    0.000000] Internal HD num: 2
[    0.000000] Internal netif num: 1
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 114104KB available (3648K code, 519K data, 124K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 794.62 BogoMIPS (lpj=3973120)
[    0.230000] Mount-cache hash table entries: 512
[    0.230000] CPU: Testing write buffer coherency: ok
[    0.230000] devtmpfs: initialized
[    0.230000] xor: measuring software checksum speed
[    0.280000]    arm4regs  :   723.600 MB/sec
[    0.330000]    8regs     :   434.400 MB/sec
[    0.380000]    32regs    :   560.800 MB/sec
[    0.380000] xor: using function: arm4regs (723.600 MB/sec)
[    0.380000] NET: Registered protocol family 16
[    0.380000] Feroceon L2: Enabling L2
[    0.380000] Feroceon L2: Cache support initialised, in WT override mode.
[    0.390000]
[    0.390000] CPU Interface
[    0.390000] -------------
[    0.390000] SDRAM_CS0 ....base 00000000, size 128MB
[    0.390000] SDRAM_CS1 ....disable
[    0.390000] SDRAM_CS2 ....disable
[    0.390000] SDRAM_CS3 ....disable
[    0.390000] PEX0_MEM ....base e0000000, size 128MB
[    0.390000] PEX0_IO ....base f2000000, size   1MB
[    0.390000] PEX1_MEM ....no such
[    0.390000] PEX1_IO ....no such
[    0.390000] INTER_REGS ....base f1000000, size   1MB
[    0.390000] NFLASH_CS ....base fa000000, size   2MB
[    0.390000] SPI_CS ....base f4000000, size  16MB
[    0.390000] BOOT_ROM_CS ....no such
[    0.390000] DEV_BOOTCS ....no such
[    0.390000] CRYPT_ENG ....base f0000000, size   2MB
[    0.390000]  Detected Tclk 200000000 and SysClk 400000000
[    0.400000] Synology 6281 1, 2 bay GPIO Init
[    0.890000] PEX0 interface detected no Link.
[    0.890000] PCI: bus0: Fast back to back transfers enabled
[    0.890000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
[    0.900000] bio: create slab <bio-0> at 0
[    0.900000] vgaarb: loaded
[    0.900000] SCSI subsystem initialized
[    0.910000] libata version 3.00 loaded.
[    1.080000] raid6: int32x1     71 MB/s
[    1.250000] raid6: int32x2     98 MB/s
[    1.420000] raid6: int32x4     92 MB/s
[    1.590000] raid6: int32x8     99 MB/s
[    1.590000] raid6: using algorithm int32x8 (99 MB/s)
[    1.590000] Switching to clocksource kw_clocksource
[    1.590000] NET: Registered protocol family 2
[    1.590000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    1.590000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    1.590000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    1.590000] TCP: Hash tables configured (established 4096 bind 4096)
[    1.590000] TCP reno registered
[    1.590000] NET: Registered protocol family 1
[    1.590000] RPC: Registered udp transport module.
[    1.590000] RPC: Registered tcp transport module.
[    1.590000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.590000] Trying to unpack rootfs image as initramfs...
[    3.520000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[    3.540000] Freeing initrd memory: 4096K
[    3.540000] XOR registered 4 channels
[    3.540000] XOR 2nd invalidate WA enabled
[    3.540000] VFS: Disk quotas dquot_6.5.2
[    3.540000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    3.540000] msgmni has been set to 231
[    3.540000] alg: No test for md5 (md5-generic)
[    3.540000] alg: No test for des (des-generic)
[    3.540000] alg: No test for des3_ede (des3_ede-generic)
[    3.540000] alg: No test for stdrng (krng)
[    3.540000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    3.540000] io scheduler noop registered
[    3.540000] io scheduler anticipatory registered (default)
[    3.560000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    3.560000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    3.570000] console [ttyS0] enabled
[    3.570000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[    3.590000] brd: module loaded
[    3.590000] sata_mv sata_mv.0: version 1.28
[    3.590000] sata_mv sata_mv.0: slots 32 ports 2
[    3.600000] scsi0 : sata_mv
[    3.600000] scsi1 : sata_mv
[    3.610000] ata1: SATA max UDMA/133 irq 21
[    3.610000] ata2: SATA max UDMA/133 irq 21
[    4.120000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    4.160000] ata1.00: ATA-9: WDC WD20EFRX-68AX9N0, 80.00A80, max UDMA/133
[    4.160000] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    4.210000] ata1.00: configured for UDMA/133
[    4.230000] scsi 0:0:0:0: Direct-Access     WDC      WD20EFRX-68AX9N0         80.0 PQ: 0 ANSI: 5
[    4.230000] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[    4.240000] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    4.250000] sd 0:0:0:0: [sda] Write Protect is off
[    4.250000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.250000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.260000]  sda: sda1 sda2 sda3
[    4.280000] sd 0:0:0:0: [sda] Attached SCSI disk
[    7.280000] Delay 5 seconds to wait for disk 2 ready.
[   12.790000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[   12.830000] ata2.00: ATA-9: WDC WD20EFRX-68AX9N0, 80.00A80, max UDMA/133
[   12.830000] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[   12.880000] ata2.00: configured for UDMA/133
[   12.900000] scsi 1:0:0:0: Direct-Access     WDC      WD20EFRX-68AX9N0         80.0 PQ: 0 ANSI: 5
[   12.900000] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[   12.910000] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[   12.920000] sd 1:0:0:0: [sdb] Write Protect is off
[   12.920000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   12.920000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   12.930000]  sdb: sdb1 sdb2 sdb3
[   12.970000] sd 1:0:0:0: [sdb] Attached SCSI disk
[   12.980000] physmap platform flash device: 00400000 at f8000000
[   12.980000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB)
[   12.990000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f0000
[   13.010000] 6 RedBoot partitions found on MTD device SYNOMTD-0
[   13.020000] SYNOMTD flash bank 0: Using RedBoot partition definition
[   13.030000] Creating 6 MTD partitions on "SYNOMTD-0":
[   13.030000] 0x000000000000-0x000000080000 : "RedBoot"
[   13.040000] 0x000000080000-0x000000280000 : "zImage"
[   13.040000] 0x000000280000-0x0000003c0000 : "rd.gz"
[   13.050000] 0x0000003c0000-0x0000003d0000 : "vendor"
[   13.060000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[   13.060000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[   13.070000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[   13.070000] serial number='A3G6N01523'
[   13.080000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config"
[   13.080000] 0x0000003f0000-0x000000400000 : "FIS directory"
[   13.090000] mvCpuIfTargetWinBaseLowGet:ERR. Getting target 11 failed.
[   13.100000] mvCpuIfTargetWinSizeGet:ERR. Getting target 11 failed.
[   13.100000]
[   13.100000] ERROR: flashInfoFill - Failed to get Device Base address and Size (spi_flash 0)Loading Marvell Ethernet Driver:
[   13.120000]   o Cached descriptors in DRAM
[   13.120000]   o DRAM SW cache-coherency
[   13.120000]   o 2 Giga ports supported
[   13.130000]   o Single RX Queue support - ETH_DEF_RXQ=0
[   13.130000]   o Single TX Queue support - ETH_DEF_TXQ=0
[   13.140000]   o TCP segmentation offload (TSO) supported
[   13.140000]   o Receive checksum offload supported
[   13.150000]   o Transmit checksum offload supported
[   13.150000]   o SKB Recycle supported - (Enabled)
[   13.160000]   o Rx descripors: q0=128
[   13.160000]   o Tx descripors: q0=532
[   13.170000]   o Loading network interface(s):
[   13.170000]     o  register under mv88fx_eth platform
[   13.180000]     o eth0, ifindex = 2, GbE port = 0
[   13.180000]     o eth0, phy chipid = 1410e40, Support WOL = 0
[   13.190000]
[   13.190000] md: linear personality registered for level -1
[   13.200000] md: raid0 personality registered for level 0
[   13.200000] md: raid1 personality registered for level 1
[   13.210000] md: raid10 personality registered for level 10
[   13.210000] md: raid6 personality registered for level 6
[   13.220000] md: raid5 personality registered for level 5
[   13.220000] md: raid4 personality registered for level 4
[   13.230000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[   13.240000] cpuidle: using governor ladder
[   13.240000] TCP cubic registered
[   13.240000] NET: Registered protocol family 17
[   13.250000] NET: Registered protocol family 15
[   13.250000] registered taskstats version 1
[   13.260000] md: Waiting for all devices to be available before autodetect
[   13.270000] md: If you don't use raid, use raid=noautodetect
[   13.270000] md: Autodetecting RAID arrays.
[   13.340000] md: invalid raid superblock magic on sda3
[   13.340000] md: sda3 does not have a valid v0.90 superblock, not importing!
[   13.400000] md: deny sdb3.
[   13.400000] md: export_rdev(sdb3)
[   13.410000] md: Scanned 6 and added 4 devices.
[   13.410000] md: autorun ...
[   13.410000] md: considering sda1 ...
[   13.420000] md:  adding sda1 ...
[   13.420000] md: sda2 has different UUID to sda1
[   13.430000] md:  adding sdb1 ...
[   13.430000] md: sdb2 has different UUID to sda1
[   13.430000] md: created md0
[   13.440000] md: bind<sdb1>
[   13.440000] md: bind<sda1>
[   13.440000] md: running: <sda1><sdb1>
[   13.450000] raid1: raid set md0 active with 2 out of 2 mirrors
[   13.450000] md0: detected capacity change from 0 to 2549678080
[   13.460000] md: considering sda2 ...
[   13.460000] md:  adding sda2 ...
[   13.470000] md:  adding sdb2 ...
[   13.470000] md: created md1
[   13.470000] md: bind<sdb2>
[   13.480000] md: bind<sda2>
[   13.480000] md: running: <sda2><sdb2>
[   13.480000] raid1: raid set md1 active with 2 out of 2 mirrors
[   13.490000] md1: detected capacity change from 0 to 534577152
[   13.490000] md: ... autorun DONE.
[   13.500000] RAMDISK: lzma image found at block 0
[   15.530000] VFS: Mounted root (ext2 filesystem) on device 1:0.
[   15.930000] usbcore: registered new interface driver usbfs
[   15.930000] usbcore: registered new interface driver hub
[   15.970000] usbcore: registered new interface driver ethub
[   15.970000] usbcore: registered new device driver usb
[   16.080000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   16.080000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[   16.090000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   16.130000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   16.150000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   16.150000] usb usb1: configuration #1 chosen from 1 choice
[   16.180000] hub 1-0:1.0: USB hub found
[   16.180000] hub 1-0:1.0: 1 port detected
[   16.450000] ds210j_synobios: module license 'Synology Inc.' taints kernel.
[   16.450000] Disabling lock debugging due to kernel taint
[   16.480000] correction with 0x03
[   16.580000] 2016-8-6 13:4:41 UTC
[   16.580000] synobios: load, major number 201
[   16.590000] Brand: Synology
[   16.590000] Model: DS-210j
[   16.590000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[   16.600000] synobios cpu_arch proc entry initialized
[   16.610000] synobios crypto_hw proc entry initialized
[   16.610000] synobios syno_platform proc entry initialized
[   16.620000] usb 1-1: new high speed USB device using orion-ehci and address 2
[   16.670000] synobios: unload
[   16.760000]  md0: unknown partition table
[   16.770000] Got empty serial number. Generate serial number from product.
[   16.780000] usb 1-1: configuration #1 chosen from 1 choice
[   16.790000] hub 1-1:1.0: USB hub found
[   16.790000] hub 1-1:1.0: 4 ports detected
[   27.980000] kjournald starting.  Commit interval 5 seconds
[   27.990000] EXT3 FS on md0, internal journal
[   27.990000] EXT3-fs: mounted filesystem with ordered data mode.
[   30.750000] kjournald starting.  Commit interval 5 seconds
[   30.770000] EXT3 FS on md0, internal journal
[   30.780000] EXT3-fs: mounted filesystem with ordered data mode.
[   30.780000] VFS: Mounted root (ext3 filesystem) on device 9:0.
[   30.790000] Trying to move old root to /initrd ... okay
[   30.840000] Freeing init memory: 124K
[   37.990000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   38.000000] sd 1:0:0:0: Attached scsi generic sg1 type 0
[   38.750000]  md1: unknown partition table
[   38.820000] Adding 522040k swap on /dev/md1.  Priority:-1 extents:1 across:522040k
[   40.190000] init: syno-auth-check main process (1023) killed by TERM signal
[   40.610000] NET: Registered protocol family 10
[   40.620000] lo: Disabled Privacy Extensions
[   40.650000] <30>systemd-udevd[1079]: starting version 204
[   43.370000] IPv6 over IPv4 tunneling driver
[   43.370000] sit0: Disabled Privacy Extensions
[   49.160000] cpufreq: Init kirkwood cpufreq driver
[   49.170000] cpufreq: High frequency: 800000KHz - Low frequency: 400000KHz
[   51.370000] alg: No test for aes (aes-generic)
[   51.680000] alg: No test for stdrng (ansi_cprng)
[   51.890000] alg: No test for crc32c (crc32c-generic)
[   52.710000] cesadev_init(bf16b000)
[   52.860000] mvCesaInit: sessions=10240, queue=64, pSram=f0000000
[   53.190000] alg: No test for sha1 (sha1-generic)
[   53.230000] alg: No test for sha224 (sha224-generic)
[   53.240000] alg: No test for sha256 (sha256-generic)
[   53.310000] alg: No test for sha384 (sha384-generic)
[   53.310000] alg: No test for sha512 (sha512-generic)
[   53.400000] encryptfs using the OCF package.
[   53.890000] alg: No test for arc4 (arc4-generic)
[   54.110000] fuse init (API version 7.13)
[   54.500000] sky2 driver version 1.25
[   54.620000] correction with 0x03
[   54.710000] 2016-8-6 13:5:19 UTC
[   54.710000] synobios: load, major number 201
[   54.720000] Brand: Synology
[   54.720000] Model: DS-210j
[   54.720000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[   54.730000] synobios cpu_arch proc entry initialized
[   54.740000] synobios crypto_hw proc entry initialized
[   54.740000] synobios syno_platform proc entry initialized
[   56.230000] eth0: mac address changed
[   59.250000] eth0: link down
[   59.250000] eth0: started
[   60.280000] eth0: link up, full duplex, speed 1 Gbps
[   62.990000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   62.990000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   64.610000] md: md2 stopped.
[   64.650000] md: bind<sdb3>
[   64.660000] md: bind<sda3>
[   64.780000] raid1: raid set md2 active with 2 out of 2 mirrors
[   64.790000] md2: detected capacity change from 0 to 996985077760
[   64.800000]  md2: unknown partition table
[   69.940000] eth0: stopped
[   71.950000] eth0: link down
[   71.960000] eth0: started
[   71.960000] eth0: change mtu 1500 (buffer-size 1536) to 9000 (buffer-size 9024)
[   73.130000] eth0: link up, full duplex, speed 1 Gbps
[   73.310000] eth0: no IPv6 routers present
[   79.560000] EXT4-fs (dm-0): barriers disabled
[   79.690000] EXT4-fs (dm-0): mounted filesystem with writeback data mode
[   79.970000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   80.220000] nf_conntrack version 0.5.0 (1851 buckets, 7404 max)
[   81.900000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   84.320000] ata1.00: configured for UDMA/133
[   84.320000] ata1: EH complete
[   84.320000] ata2.00: configured for UDMA/133
[   84.330000] ata2: EH complete
[   85.640000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   86.340000] Initializing USB Mass Storage driver...
[   86.350000] usbcore: registered new interface driver usb-storage
[   86.350000] USB Mass Storage support registered.
[   86.650000] usbcore: registered new interface driver usblp
[   87.290000] usbcore: registered new interface driver hiddev
[   87.300000] usbcore: registered new interface driver usbhid
[   87.300000] usbhid: v2.6:USB HID core driver
[   91.700000] ata1.00: configured for UDMA/133
[   91.700000] ata1: EH complete
[   92.060000] ata2.00: configured for UDMA/133
[   92.060000] ata2: EH complete
[  120.680000] loop: module loaded
[  124.770000] Slow work thread pool: Starting up
[  125.260000] Slow work thread pool: Ready
[  163.640000] findhostd uses obsolete (PF_INET,SOCK_PACKET)
 

Modifié le 6 août 2016 par zheniar

[gaetan.cambier]

L'important n'est pas forcément d'avoir un retour à la commande, c'est de savoir ce quel retourne ;)

tu est probablement en raid pur et dur et pas de shr

que retourne la commande suivante ?

mount

Bon, après, on passe aux choses sérieuses 

[zheniar]

il y a 9 minutes, gaetan.cambier a dit :

L'important n'est pas forcément d'avoir un retour à la commande, c'est de savoir ce quel retourne ;)

tu est probablement en raid pur et dur et pas de shr

que retourne la commande suivante ?

mount

Bon, après, on passe aux choses sérieuses 

Ok,

ci dessous le mount

DiskStation> mount
/dev/root on / type ext3 (defaults)
/sys on /sys type sysfs (0)
none on /dev/pts type devpts (gid=4,mode=620)
/tmp on /tmp type tmpfs (0)
/run on /run type tmpfs (rw,nosuid,nodev,relatime,mode=755)
/dev/shm on /dev/shm type tmpfs (rw,nosuid,nodev,relatime)
/proc/bus/usb on /proc/bus/usb type usbfs (0)
/dev/mapper/vol1-origin on /volume1 type ext4 (usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,synoacl)
 

[gaetan.cambier]

pour moi, il y a un problème de taille sur le md2 du raid 

donc, on va reglé cela en mode debug :

syno_poweroff_task -d

après cette commande, SEUL le ssh sera fonctionnel, c'est NORMAL

ensuite :

mdadm --grow /dev/md2 --size=max
cat /proc/mdstat

si tu veux sortir du mode debug, la commande magique est :

reboot

mais tant que l'on n'a pas fini, c'est pas vraiment utile ;)

Continue les copié collé de ce que retourne le terminal ;)

[zheniar]

Voici ce que ca donne. je suis aveuglement car c'est du chinois pour moi, malheureusement.

Merci en tout cas pour votre temps

DiskStation> syno_poweroff_task -d
DiskStation> mdadm --grow /dev/md2 --size=max
mdadm: component size of /dev/md2 has been set to 973618240K
DiskStation> cat /proc/mdstat
Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4]
md2 : active raid1 sda3[0] sdb3[1]
      973618240 blocks super 1.2 [2/2] [UU]

md1 : active raid1 sda2[1] sdb2[0]
      522048 blocks [2/2] [UU]

md0 : active raid1 sda1[1] sdb1[0]
      2489920 blocks [2/2] [UU]

unused devices: <none>
 

[gaetan.cambier]

vgchange -ay
pvdisplay
vgdisplay
lvdisplay

 

[zheniar]

il y a 2 minutes, gaetan.cambier a dit :

vgchange -ay
pvdisplay
vgdisplay
lvdisplay

 

DiskStation> vgchange -ay
DiskStation> pvdisplay
DiskStation> vgdisplay
DiskStation> lvdisplay
DiskStation>
 

[gaetan.cambier]

bon dans ce cas :

resize2fs /dev/md2

ca devrait agrandir ton volume

[zheniar]

il y a 9 minutes, gaetan.cambier a dit :

bon dans ce cas :

resize2fs /dev/md2

ca devrait agrandir ton volume

voici la reponse du système, c'est bizarre...

je reboot pour voir?

DiskStation> resize2fs /dev/md2
resize2fs 1.42.6 (21-Sep-2012)
The filesystem is already 243404560 blocks long.  Nothing to do! (Device size is 243404560 blocks long)
 

[zheniar]

En désespoir de cause j'ai fini par supprimer le volume pour en recréer un, en SHR cette fois.

Merci en tout cas pour votre temps et votre aide ! :)